A basic demonstration for roofing contractors and homeowners on how to install GAF Pro-Start Starter Strip Shingles. Learn more at https://www.gaf.com/en-us/products/pro-start Pro Series by GAF provides step-by-step instructions on how to install GAF roofing products for better safety and efficiency. Video details include starter strip preparation, shingle measurements and placement, and nailing instructions. Ver en Español: https://youtu.be/GLEN60mJcNo

A basic demonstration for roofing contractors and homeowners on how to install GAF Pro-Start Starter Strips at Valleys and Hips. Learn more at https://www.gaf.com/en-us/products/pro-start Pro Series by GAF provides step-by-step instructions on how to install GAF roofing products for better safety and efficiency. Video details include valley installation instructions and hip installation instructions. Ver en Español: https://youtu.be/m3-PcMnqCR0

GAF - Mastering The Roof (chapter 09) This video demonstrates the proper installation technique for GAF starter strips; a superior alternative to starter shingles. Starter strips are important for wind resistance. Use WeatherBlocker or ProStart starter strips. One of the most common sources of failure in a roof system is the improper installation of starter shingles. This starter course is very important, especially for wind resistance. GAF offers Pro-Start and WeatherBlocker starter strips that are manufactured with a perforated line. This feature is a real time saver by eliminating the need to manually cut and cleanup shingles tabs. Along with convenience and savings; the Pro-Start and WeatherBlocker products utilizing advanced Dura Grip adhesive to achieve maximum protection against wind blow-offs. Now that we have covered the importance and benefits of GAF precut starter strips lets take a look at they install. For shingles exposure less than six inches, the use of either Pro-start or Weatherblocker starter strips can be used. For such applications; begin by separating the strip at the perforated line. When applying shingles with exposures greater than 6 inches, such as the Camelot collection, only full un-split WeatherBlocker starter strip can be used. Place the appropriate sized starter strip with the sealant facing up at the eave edge. For proper water drainage, Both Pro-Start and Weatherblocker starter strip require a one quarter to three quarter inches overhang at all eave and rake edges. Every Starter strip requires a minimum of four nails driven in a linear fashion one and a half to three inches above the shingle's bottom edge. Begin with the first nail at a distance of one and a half to three inches from the beginning side edge. Space the remaining three nails ten to twelve inches from the previous nail, and the fourth nail one to two inches from the ending edge. When installing Metric dimensioned shingles, you must trim five inches off the first WeatherBlocker starter strip or three inches off the first ProStart starter strip. This critical step ensures that the starter strip butt joints and overlapping shingles butt joints are off-set a minimum of four inches. Depending on the length of the shingle being installed, A 10 to12 inch section of starter strip may periodically need to be cut and installed to meet the required 4 inch offset. Fasten the adjustment starter strip with two nails one to two inches from each side end. For maximum wind resistance, starter strips should be installed along all rake edges. Begin by laying the strip with the sealant side up, closest to the rake edge. Position the starter strip so that it overlaps the eave starter strip by at least three inches. As with the eave edges, the Starter strip must overhang the rake edge one quarter to three quarters of an inch. Begin the line of nail fasteners one to two inches from the side edge of the starter strip, and one and a one half to three inches from the rake edge. Complete the rake edge starter course by nailing along a vertical line every ten to twelve inches up the rake until reaching the ridge. Learn more about Starter Strip Shingles at: https://www.gaf.com/en-us/roofing-products/residential-roofing-products/starter-strip-shingles

Watch this video about the key components that make up the GAF Roofing System, more than just shingles, it’s a system built to protect. The six layers of protection that work together to keep your home safe include: leak barrier, roof deck protection, starter strip shingles, asphalt shingles, attic ventilation, and ridge cap shingles. Learn more at: https://www.gaf.com/en-us/for-homeowners/lifetime-roofing-system More homes and businesses in the U.S. are protected by a GAF roof than by any other product. We are the leading roofing manufacturer in North America, with plants strategically located across the U.S. As a Standard Industries company, GAF is part of the largest roofing and waterproofing business in the world. Connect with us: Find us at: https://www.gaf.com/ Follow us on LinkedIn: https://www.linkedin.com/company/gaf/ Follow us on Twitter: https://twitter.com/gafroofing Like us on Facebook: https://www.facebook.com/GAFRoofing/ Follow us on Instagram: https://www.instagram.com/gafroofing/

En este video, lo llevaremos paso a paso por la instalación de las tejas de tira inicial GAF Pro-Start. Watch in English: https://youtu.be/mCjlS_gyH5k

En este video, lo llevaremos paso a paso por la instalación de las tejas de tira inicial GAF Pro-Start en valles y sobre faldones. Watch in English: https://youtu.be/J0_qdqGL4yI